1 files changed, 0 insertions, 116 deletions
diff --git a/oggcast~/readme b/oggcast~/readme
deleted file mode 100644
index b3090ec..0000000
--- a/oggcast~/readme
+++ /dev/null
@@ -1,116 +0,0 @@
-Version 0.2
-copyright (c) 2002 by Olaf Matthes
-
-oggcast~ is a ogg/vorbis streaming external for pd (by Miller 
-Puckette) that connects to an IceCast2 server.
-
-
-To run oggcast~ place the file oggcast~.dll for win or oggcast~.pd_linux 
-in the directory of our patch or start pd with '-lib oggcast~' flag. 
-
-To compile oggcast~ on Linux get the ogg/vorbice library from 
-http://www.vorbis.com/.
-You have to modify the makefile to make it point to the place where the
-ogg/vorbis library is.
-
-
-This software is published under LGPL terms.
-
-This is software with ABSOLUTELY NO WARRANTY.
-Use it at your OWN RISK. It's possible to damage e.g. hardware or your hearing
-due to a bug or for other reasons. 
-
-*****************************************************************************
-
-oggcast~ uses the ogg/vorbice library to encode audio data.
-The latest version of ogg/vorbis can be found at http://www.vorbice.com/
-
-Below is the original copyright information taken from the ogg/vorbis library:
-
-
-Copyright (c) 2001, Xiphophorus
-
-Redistribution and use in source and binary forms, with or without
-modification, are permitted provided that the following conditions
-are met:
-
-- Redistributions of source code must retain the above copyright
-notice, this list of conditions and the following disclaimer.
-
-- Redistributions in binary form must reproduce the above copyright
-notice, this list of conditions and the following disclaimer in the
-documentation and/or other materials provided with the distribution.
-
-- Neither the name of the Xiphophorus nor the names of its contributors
-may be used to endorse or promote products derived from this software
-without specific prior written permission.
-
-THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
-``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
-A PARTICULAR PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE REGENTS OR
-CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
-EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-
-*****************************************************************************
-
-Usage:
-
-Use message "vbr <samplerate> <channels> <quality>" to set the vorbis
-encoding parameters. Resampling is currently not supported, so 'samplerate' 
-should be the one pd is running at. 'channels' specyfies the number of channels 
-to stream. This can be set to 2 (default) or 1 which means mono stream taking
-the leftmost audio input only. 'quality' can be a value between 0.0 and 1.0 
-giving the quality of the stream. 0.4 (default) results in a stream that's 
-about 128kbps. 
-
-Since Vorbis uses VBR encoding, bitrates vary depending on the type of audio
-signal to be encoded. A pure sine [osc~] results in the smalest stream, com-
-plex audio signals will increase this value significantly. To test the maximum 
-bitrate that might occur for a quality setting use noise~ as signal input.
-
-Use message "vorbis <samplerate> <channels> <maximum bitrate> <nominal bit-
-rate> <minimal bitrate>" to set encoding quality on the basis of bitrates.
-When setting all three bitrate parameters to the same value one gets a
-constant bitrate stream. Values are in kbps!
-
-Message "connect <host> <mountpoint> <port>" connects to the IceCast2 server.
-Note that no response about succesfull connection is send by the server. All
-messages in the pd console window about connection status depend on the ability
-to send data to the server.
-The mountpoint should end with '.ogg' to indiocate to the player/client that 
-it is an ogg/vorbis encoded stream.
-
-Use "passwd <passwort>" to set your password (default is 'letmein') and 
-"disconnect" to disconnect from the server. "print" prints out the current
-vorbis encoder settings.
-
-To set the comment tags in the ogg/vorbis header (which can be displayed by
-the receiving client) use message "<NAMEOFTAG> <comment>". Supported tags are:
-TITLE, ARTIST, GENRE, PERFORMER, LOCATION, COPYRIGHT, CONTACT, DESCRIPTION and
-DATE (which is automatically set to the date/time the broadcast started). To
-get spaces use '=' or '_' instead. Note that under Win2k '=' sometimes get lost 
-from the patch after saving!!!
-
-
-Listening to it:
-
-To listen to ogg/vorbis encoded livestreams many player need an extra plug-in.
-Have a look at http://www.vorbis.com/ to find the appropiate plug-in for your
-player.
-To play back the stream just open lacation http://<server>:<port>/<mountpoint>.
-
-Note that changing encoding parameters or header comments while oggcast~ is
-streaming to the server might result in audible dropouts.
-
-
-
-Latest version can be found at:
-http://www.akustische-kunst.de/puredata/
-
-Please report any bugs to olaf.matthes@gmx.de!
-\ No newline at end of file