aboutsummaryrefslogtreecommitdiff
path: root/Pd_firmware/Pd_firmware.pde
diff options
context:
space:
mode:
Diffstat (limited to 'Pd_firmware/Pd_firmware.pde')
-rw-r--r--Pd_firmware/Pd_firmware.pde256
1 files changed, 138 insertions, 118 deletions
diff --git a/Pd_firmware/Pd_firmware.pde b/Pd_firmware/Pd_firmware.pde
index 3eabc7d..a0ca913 100644
--- a/Pd_firmware/Pd_firmware.pde
+++ b/Pd_firmware/Pd_firmware.pde
@@ -56,7 +56,7 @@
* TODO: use Program Control to load stored profiles from EEPROM
*/
-/* cvs version: $Id: Pd_firmware.pde,v 1.23 2007-02-20 06:25:56 eighthave Exp $ */
+/* cvs version: $Id: Pd_firmware.pde,v 1.24 2007-02-22 06:16:43 eighthave Exp $ */
/*==========================================================================
* MESSAGE FORMATS
@@ -168,7 +168,8 @@
#define MAJOR_VERSION 1 // for non-compatible changes
#define MINOR_VERSION 0 // for backwards compatible changes
-/* total number of digital pins supported */
+/* total number of pins currently supported */
+#define TOTAL_ANALOG_PINS 16
#define TOTAL_DIGITAL_PINS 14
// for comparing along with INPUT and OUTPUT
@@ -206,6 +207,9 @@ int digitalPinStatus = 0;
* the rest of the bits are unused and should remain 0 */
int pwmStatus = 0;
+/* bit-wise array to store pin reporting */
+unsigned int analogPinsToReport = 65536;
+
/*==========================================================================
* FUNCTIONS
@@ -215,17 +219,17 @@ int pwmStatus = 0;
* output digital bytes received from the serial port
*/
void outputDigitalBytes(byte pin0_6, byte pin7_13) {
- int i;
- int mask;
- int twoBytesForPorts;
-
- twoBytesForPorts = pin0_6 + (pin7_13 << 7);
- for(i=0; i<14; ++i) {
- mask = 1 << i;
- if( (digitalPinStatus & mask) && !(pwmStatus & mask) ) {
- digitalWrite(i, twoBytesForPorts & mask);
- }
- }
+ int i;
+ int mask;
+ int twoBytesForPorts;
+
+ twoBytesForPorts = pin0_6 + (pin7_13 << 7);
+ for(i=0; i<14; ++i) {
+ mask = 1 << i;
+ if( (digitalPinStatus & mask) && !(pwmStatus & mask) ) {
+ digitalWrite(i, twoBytesForPorts & mask);
+ }
+ }
}
/* -------------------------------------------------------------------------
@@ -233,60 +237,60 @@ void outputDigitalBytes(byte pin0_6, byte pin7_13) {
* Arduino's serial port. This is where the commands are handled.
*/
void processInput(int inputData) {
- int command, channel;
-
- // a few commands have byte(s) of data following the command
- if( (waitForData > 0) && (inputData < 128) ) {
- waitForData--;
- storedInputData[waitForData] = inputData;
- if( (waitForData==0) && executeMultiByteCommand ) {
- //we got everything
- switch(executeMultiByteCommand) {
- case ANALOG_MESSAGE:
- channel = inputData & 0x0F; // get channel from command byte
- break;
- case DIGITAL_MESSAGE:
- outputDigitalBytes(storedInputData[1], storedInputData[0]);
- break;
- case SET_DIGITAL_PIN_MODE:
- setPinMode(storedInputData[1], storedInputData[0]);
- break;
- case REPORT_ANALOG_PIN:
- break;
- case REPORT_DIGITAL_PORTS:
- break;
- }
- executeMultiByteCommand = 0;
- }
- } else {
- // remove channel info from command byte if less than 0xF0
- if(inputData < 0xF0) {
- command = inputData & 0xF0;
- } else {
- command = inputData;
- }
- switch (inputData) {
- case ANALOG_MESSAGE:
- case DIGITAL_MESSAGE:
- case SET_DIGITAL_PIN_MODE:
- waitForData = 2; // two data bytes needed
- executeMultiByteCommand = inputData;
- break;
- case REPORT_ANALOG_PIN:
- case REPORT_DIGITAL_PORTS:
- waitForData = 1; // two data bytes needed
- executeMultiByteCommand = inputData;
- break;
- case SYSTEM_RESET:
- // this doesn't do anything yet
- break;
- case REPORT_VERSION:
- Serial.print(REPORT_VERSION, BYTE);
- Serial.print(MAJOR_VERSION, BYTE);
- Serial.print(MINOR_VERSION, BYTE);
- break;
- }
- }
+ int command, channel;
+
+ // a few commands have byte(s) of data following the command
+ if( (waitForData > 0) && (inputData < 128) ) {
+ waitForData--;
+ storedInputData[waitForData] = inputData;
+ if( (waitForData==0) && executeMultiByteCommand ) {
+ //we got everything
+ switch(executeMultiByteCommand) {
+ case ANALOG_MESSAGE:
+ channel = inputData & 0x0F; // get channel from command byte
+ break;
+ case DIGITAL_MESSAGE:
+ outputDigitalBytes(storedInputData[1], storedInputData[0]);
+ break;
+ case SET_DIGITAL_PIN_MODE:
+ setPinMode(storedInputData[1], storedInputData[0]);
+ break;
+ case REPORT_ANALOG_PIN:
+ break;
+ case REPORT_DIGITAL_PORTS:
+ break;
+ }
+ executeMultiByteCommand = 0;
+ }
+ } else {
+ // remove channel info from command byte if less than 0xF0
+ if(inputData < 0xF0) {
+ command = inputData & 0xF0;
+ } else {
+ command = inputData;
+ }
+ switch (inputData) {
+ case ANALOG_MESSAGE:
+ case DIGITAL_MESSAGE:
+ case SET_DIGITAL_PIN_MODE:
+ waitForData = 2; // two data bytes needed
+ executeMultiByteCommand = inputData;
+ break;
+ case REPORT_ANALOG_PIN:
+ case REPORT_DIGITAL_PORTS:
+ waitForData = 1; // two data bytes needed
+ executeMultiByteCommand = inputData;
+ break;
+ case SYSTEM_RESET:
+ // this doesn't do anything yet
+ break;
+ case REPORT_VERSION:
+ Serial.print(REPORT_VERSION, BYTE);
+ Serial.print(MINOR_VERSION, BYTE);
+ Serial.print(MAJOR_VERSION, BYTE);
+ break;
+ }
+ }
}
@@ -300,8 +304,8 @@ void processInput(int inputData) {
* Therefore, it only checks for input once per cycle of the serial port.
*/
void checkForInput() {
- if(Serial.available())
- processInput( Serial.read() );
+ if(Serial.available())
+ processInput( Serial.read() );
}
// -------------------------------------------------------------------------
@@ -309,71 +313,87 @@ void checkForInput() {
* bits in the two bit-arrays that track Digital I/O and PWM status
*/
void setPinMode(byte pin, byte mode) {
- if(mode == INPUT) {
- digitalPinStatus = digitalPinStatus &~ (1 << pin);
- pwmStatus = pwmStatus &~ (1 << pin);
- pinMode(pin,INPUT);
- }
- else if(mode == OUTPUT) {
- digitalPinStatus = digitalPinStatus | (1 << pin);
- pwmStatus = pwmStatus &~ (1 << pin);
- pinMode(pin,OUTPUT);
- }
- else if( mode == PWM ) {
- digitalPinStatus = digitalPinStatus | (1 << pin);
- pwmStatus = pwmStatus | (1 << pin);
- pinMode(pin,OUTPUT);
- }
-// TODO: save status to EEPROM here, if changed
+ if(mode == INPUT) {
+ digitalPinStatus = digitalPinStatus &~ (1 << pin);
+ pwmStatus = pwmStatus &~ (1 << pin);
+ pinMode(pin,INPUT);
+ }
+ else if(mode == OUTPUT) {
+ digitalPinStatus = digitalPinStatus | (1 << pin);
+ pwmStatus = pwmStatus &~ (1 << pin);
+ pinMode(pin,OUTPUT);
+ }
+ else if( mode == PWM ) {
+ digitalPinStatus = digitalPinStatus | (1 << pin);
+ pwmStatus = pwmStatus | (1 << pin);
+ pinMode(pin,OUTPUT);
+ }
+ // TODO: save status to EEPROM here, if changed
}
// =========================================================================
// used for flashing the pin for the version number
void pin13strobe(int count, int onInterval, int offInterval) {
- byte i;
- for(i=0; i<count; i++) {
- digitalWrite(13,1);
- delay(onInterval);
- digitalWrite(13,0);
- delay(offInterval);
- }
+ byte i;
+ for(i=0; i<count; i++) {
+ digitalWrite(13,1);
+ delay(onInterval);
+ digitalWrite(13,0);
+ delay(offInterval);
+ }
}
/*==========================================================================
* SETUP()
*==========================================================================*/
void setup() {
- byte i;
-
-// TODO: load state from EEPROM here
- Serial.begin(115200); // 9600, 14400, 38400, 57600, 115200
-
-/* TODO: send digital inputs here, if enabled, to set the initial state on the
- * host computer, since once in the loop(), the Arduino will only send data on
- * change. */
-
-// flash the pin 13 with the protocol minor version (add major once > 0)
- pinMode(13,OUTPUT);
- pin13strobe(10,5,20); // separator, a quick burst
- delay(500);
- pin13strobe(MAJOR_VERSION, 200, 400);
- delay(500);
- pin13strobe(10,5,20); // separator, a quick burst
- delay(500);
- pin13strobe(MINOR_VERSION, 200, 400);
- delay(500);
- pin13strobe(10,5,20); // separator, a quick burst
- delay(1000);
- for(i=0; i<TOTAL_DIGITAL_PINS; ++i) {
- setPinMode(i,OUTPUT);
- }
+ byte i;
+
+ // TODO: load state from EEPROM here
+ Serial.begin(115200); // 9600, 14400, 38400, 57600, 115200
+
+ /* TODO: send digital inputs here, if enabled, to set the initial state on the
+ * host computer, since once in the loop(), the Arduino will only send data on
+ * change. */
+
+ // flash the pin 13 with the protocol minor version (add major once > 0)
+ pinMode(13,OUTPUT);
+ pin13strobe(10,5,20); // separator, a quick burst
+ delay(500);
+ pin13strobe(MAJOR_VERSION, 200, 400);
+ delay(500);
+ pin13strobe(10,5,20); // separator, a quick burst
+ delay(500);
+ pin13strobe(MINOR_VERSION, 200, 400);
+ delay(500);
+ pin13strobe(10,5,20); // separator, a quick burst
+ delay(1000);
+ for(i=0; i<TOTAL_DIGITAL_PINS; ++i) {
+ setPinMode(i,OUTPUT);
+ }
}
/*==========================================================================
* LOOP()
*==========================================================================*/
void loop() {
-
- checkForInput();
+ int i; // counter for analog pins
+ int analogData;
+
+ checkForInput();
+ /* get analog in, for the number enabled */
+ for(i=0; i<TOTAL_ANALOG_PINS; ++i) {
+ checkForInput();
+ //if( analogPinsToReport & (1 << i) ) {
+ analogData = analogRead(i);
+ /* These two bytes get converted back into the whole number on host.
+ Highest bits should be zeroed so the 8th bit doesn't get set */
+ checkForInput();
+ Serial.print(ANALOG_MESSAGE + i, BYTE);
+ Serial.print(analogData % 128, BYTE); // mod by 32 for the small byte
+ Serial.print(analogData >> 7, BYTE); // shift high bits into output byte
+ //}
+ checkForInput();
+ }
}
generated by cgit v1.2.1 (git 2.18.0) at 2024-06-02 10:14:51 +0000