aboutsummaryrefslogtreecommitdiff
path: root/arduino-test.pd
AgeCommit message (Collapse)Author
2010-03-18fixed up logic for reseting the GUI elements when opening an serial portHans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=13229
2010-03-17cleaned up patch to remove optional analogIns and digitalIns messages and ↵Hans-Christoph Steiner
focus on the pinMode message; also cleaned up layout to make it clearer svn path=/trunk/externals/hardware/arduino/; revision=13219
2010-02-19updated so that you can use pins 0 and 1 for boards like the TeensyHans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=13176
2009-10-05set the radio buttons for the analog pins to default to the analog settingHans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=12535
2009-07-10changed pwm stuff to analogHans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=11856
2009-07-01added GUIs for using analog pins as digital, and made extended pinMode GUI ↵Hans-Christoph Steiner
for new modes svn path=/trunk/externals/hardware/arduino/; revision=11841
2009-06-26added support for new samplingInterval messageHans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=11821
2008-11-25- added a "port" message for sending a complete port at a time, directlyHans-Christoph Steiner
reflecting the underlying digital message and the fact that digital outputs on a microcrontroller are handled on an 8-bit port basis. svn path=/trunk/externals/hardware/arduino/; revision=10379
2008-09-08implemented GUI reset, so that whenever you reopen the device, all of the ↵Hans-Christoph Steiner
GUIs get reset to their initial state to match the arduino's state svn path=/trunk/externals/hardware/arduino/; revision=10282
2008-09-08- moved protocol version and firmware name to the status outletHans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=10281
2008-09-08- removed old, debug right/cold inlet from [arduino]Hans-Christoph Steiner
- converted the right outlet on [arduino] to output status info, as it should be. Right now, it is just info directly from [comport]. svn path=/trunk/externals/hardware/arduino/; revision=10280
2008-09-08set pinMode toggles to 1 since StandardFirmata defaults to OUTPUT mode on ↵Hans-Christoph Steiner
digital pins; a couple minor cleanups as well svn path=/trunk/externals/hardware/arduino/; revision=10279
2008-04-17- implemented v2.0 protocol changes, including the order change for theHans-Christoph Steiner
protocol version report svn path=/trunk/externals/hardware/arduino/; revision=9715
2008-04-14- working on Firmata v2.0, got digital inputs and the toggling ofdigital portHans-Christoph Steiner
reporting working svn path=/trunk/externals/hardware/arduino/; revision=9699
2008-04-11First stab at implementing v2 of the protocol, digitalWrite works, but no luckHans-Christoph Steiner
yet with digital input. I am not sure if the problem is in Pd or Firmata. svn path=/trunk/externals/hardware/arduino/; revision=9692
2008-04-09implemented both directions of Firmata string and generic sysex message support Hans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=9689
2008-04-08Implemented firmware reporting and sysex, sysex isn't fully tested.Hans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=9685
2007-06-27added the [devices( message to the test patch; applied David Mellis' patch ↵Hans-Christoph Steiner
to get things working with Arduino-0008 svn path=/trunk/externals/hardware/arduino/; revision=7801
2007-03-08cleaned up for the Pduino 0.3 releaseHans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=7476
2007-03-06- got digital inputs working reading by port, sends only on changeHans-Christoph Steiner
- ignore Rx/Tx pins (0 and 1) since they are used for serial/USB - removed a fair amount of cruft svn path=/trunk/externals/hardware/arduino/; revision=7469
2007-03-05- Removed lots of cruft and various attempts at fixing things.Hans-Christoph Steiner
- Removed timer2 interrupt code because it was interfering with the hardware PWM on some pins. Replaced it with timer0_overflow_count from wiring.c but that's not fully functional yet, I think I have to get the time units right. Right now it seems to just output everytime rather than every 4ms - removed second [arduino] object in arduino-test.pd that was causing lost serial data. WORKING - analog input working - hardware PWM output working - digital output working - setPinMode to INPUT/OUTPUT for digital pins working NOT WORKING YET - digital inputs - software PWM on non-hardware-PWM pins - save state to EEPROM svn path=/trunk/externals/hardware/arduino/; revision=7468
2007-02-22- got analog input workingHans-Christoph Steiner
- version reporting works, but checkInput() isn't run enough, so it misses the data if there is a lot of traffic on the serial port svn path=/trunk/externals/hardware/arduino/; revision=7444
2006-10-31added [digital 5 1( messages for digital inputHans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=6200
2006-10-31got analog inputs converted to new message format, the foundation is laid ↵Hans-Christoph Steiner
for digital inputs... svn path=/trunk/externals/hardware/arduino/; revision=6197
2006-10-30switched over to [digital 5 1( message format for output, . next for the ↵Hans-Christoph Steiner
hard part, switch over analog and digital to this message format svn path=/trunk/externals/hardware/arduino/; revision=6182
2006-09-29added 'hardware' to the [import] so that [arduino] will loadHans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=6056
2006-09-15redesigned the input protocol to be a 3-byte sequence, the first byte is theHans-Christoph Steiner
data type, the second two are the data. The second two bytes are then combined to give one 14-bit value. For example 240 0 1 (from serial) == [version 1( (Pd message) arduino-test.pd was updated for this, the help patch was not, but should be largely correct. I only tightened up the layout of the help patch. svn path=/trunk/externals/hardware/arduino/; revision=5936
2006-09-04switched to default to output mode so that you don't see voltage float on ↵Hans-Christoph Steiner
disconnected pins; changed test patch init settings to reflect initial state of arduino svn path=/trunk/externals/hardware/arduino/; revision=5865
2006-09-03arduino-test.pdHans-Christoph Steiner
svn path=/trunk/externals/hardware/arduino/; revision=5859